BOARDS
======
501-1007
May have to jump J1600 on monochrome framebuffer 501-1052-01/02 when
used with boot ROM N or below and SunOS 3.0 or later.
501-1051
May have to jump J1600 on monochrome framebuffer 501-1052-01/02 when
used with boot ROM N or below and SunOS 3.0 or later.
501-1074
To use a VME 32-bit data device (e.g. MCP, HSI, ALM-2, SCA, or
"Sun-3" SCSI (?)), the board revision must be 501-1074-22 or later.
501-1075, 501-1133, 501-1162, 501-1207
The 370-1011 Sysgen SC4000 SCSI/QIC-02 tape controller does not work
with this motherboard under SunOS 3.3.
501-1094
To use a VME 32-bit data device (e.g. MCP, HSI, ALM-2, SCA, or
"Sun-3" SCSI (?)), the CPU revision must be 501-1094-22 or later.
501-1100
The minimum board revision required for use with the 501-1125 or
501-1214 IPC is 501-1100-06.
501-1134
To use a VME 32-bit data device (e.g. MCP, HSI, ALM-2, SCA, or
"Sun-3" SCSI (?)), the board revision must be 501-1134-06 or later.
501-1163
To use a VME 32-bit data device (e.g. MCP, HSI, ALM-2, SCA, TAAC-1,
or "Sun-3" SCSI), the board revision must be 501-1163-09 or later.
501-1164
To use a VME 32-bit data device (e.g. MCP, HSI, ALM-2, SCA, TAAC-1,
or "Sun-3" SCSI), the board revision must be 501-1164-09 or later.
501-1199
The board revision must be 501-1199-11 or later to use a type-4
keyboard.
The 501-1384 FPU2 is not supported on this board.
The P4 cgsix color framebuffer (501-1374, 501-1505, 501-1532)
requires boot ROM version 3.0 or later to use it as the console.
501-1205, 501-1322, 501-1334
The P4 cgsix color framebuffer (501-1374, 501-1505, 501-1532)
requires boot ROM version 3.0 or later to use it as the console.
501-1206
The minimum board revision required for use with the 501-1125 or
501-1214 IPC is 501-1206-06.
501-1208
Board revisions 501-1208-04 or lower may fail with non-Sun boards.
Use 501-1208-05 or later.
501-1237
The board revision must be 501-1237-11 or later to use a type-4
keyboard.
The 501-1384 FPU2 is not supported on this board.
The P4 cgsix color framebuffer (501-1374, 501-1505, 501-1532)
requires boot ROM version 3.0 or later to use it as the console.
501-1241
The GXi color framebuffer 501-1352 requires boot ROM version 4.3 or
later.
The low-resolution monochrome framebuffer 501-1433 (and 501-1568?)
requires boot ROM version 4.4 or later.
Board revision 501-1241-02 Rev 03 or later is required to use
dynamic memory boards 501-1394, 501-1441, or 501-1423 (555-1423).
Board revision 501-1241-04 Rev 01 or later is required to use
multiple dynamic memory boards.
501-1274
The board revision must be 501-1274-12 or later to use a type-4
keyboard.
The board revision must be 501-1274-13 or later to use a 501-1249
Xylogics 7053 SMD controller.
501-1576 16M memory boards require boot ROM version 3.0 or later
when two or more are present.
501-1299
If memory boards are installed on both sides of this board, the
terminator pack at U1411 should be removed.
If the 501-1105 FPA or 501-1446 FPA+ is being used with this board,
any 8M memory cards must be 501-1102-11 or later.
This board is not compatible with 501-1254 32M memory boards.
However, it is compatible with the similar 501-1451 32M memory
boards.
P4-based cgeight framebuffers must be 501-1371-04 or later for use
with this board.
Jumpers P10, P11, P12, and P13 should be removed from the 501-1598
and 501-1832 backplanes when this board is installed.
This board may not be compatible with the SunLink Channel Adapter --
the 501-1550 board may be required instead.
501-1316
Board revision 501-1316-03 or later is required to use the 501-1267
cgfive framebuffer.
Board revision 501-1316-04 or later is required to use the 501-1539
or 501-1855 ISP-80/IPI-2 disk controller or 501-1276 FDDI
controller.
The 501-1371 P4 cgeight framebuffer must be -04 or later for use
with this board.
501-1324, 501-1413
The GXi color framebuffer 501-1352 requires boot ROM version 4.3 or
later.
The low-resolution monochrome framebuffer 501-1433 (and 501-1568?)
requires boot ROM version 4.4 or later.
501-1381
The 501-1381 is not supported in the 4/470 serial numbers 136Kxxxx
and greater. This chassis has two 50-pin SCSI-2 connectors on the
rear EMI cover.
The 501-1721 128M memory board requires boot ROM version 3.0 or
later.
The 501-1537/1538 VX/MVX Visualization Accelerator requires boot ROM
version 4.1.1 or later when used as the console.
501-1382, 501-1629
The 501-1667 Load Board should be installed in systems without disk
drives or SBus cards.
501-1414
The GXi color framebuffer 501-1352 requires boot ROM version 4.3 or
later.
The low-resolution monochrome framebuffer 501-1433 (and 501-1568?)
requires boot ROM version 4.4 or later.
501-1462, 501-1463, 501-1464, 501-1465
The 501-1384 FPU2 is not supported on this board.
The P4 cgsix color framebuffer (501-1374, 501-1505, 501-1532)
requires boot ROM version 3.0 or later to use it as the console.
501-1491, 501-1522
501-1576 16M memory boards require boot ROM version 3.0 or later
when two or more are present.
501-1512, 501-1513, 501-1514, 501-1515, 501-1516, 501-1517
The 501-1384 FPU2 *is* supported on this board.
The P4 cgsix color framebuffer (501-1374, 501-1505, 501-1532)
requires boot ROM version 3.0 or later to use it as the console.
501-1550
If memory boards are installed on both sides of this board, the
terminator pack at U1411 should be removed.
If the 501-1105 FPA or 501-1446 FPA+ is being used with this board,
any 8M memory cards must be 501-1102-11 or later.
This board is not compatible with 501-1254 32M memory boards.
However, it is compatible with the similar 501-1451 32M memory
boards.
P4-based cgeight framebuffers must be 501-1371-04 or later for use
with this board.
Jumpers P10, P11, P12, and P13 should be removed from the 501-1598
and 501-1832 backplanes when this board is installed.
Board 501-1550-10 or later is required for use with the SunLink
Channel Adapter.
501-1632
The 501-1667 Load Board should be installed in systems without disk
drives or SBus cards.
501-1638, 501-1744, 501-1858, 501-1859, 501-1912, 501-1926, 501-1989,
501-1995, 501-2495, 501-2505, 501-2506
The 501-1667 Load Board should be installed in systems without disk
drives or SBus cards.
501-1656, 501-1657, 501-1658, 501-1659, 501-1660, 501-1661
The P4 cgsix color framebuffer (501-1374, 501-1505, 501-1532)
requires boot ROM version 3.0 or later to use it as the console.
501-1689
SCSI bus errors may occur when multiple SCSI devices are used with
boards below 501-1689-06.
Boards below 501-1689-07 fail SunDiag floppy drive testing.
501-1733, 501-2259, 501-2365
When two 501-2358 SM40 MBus modules are installed, boot ROM version
2.12 is required.
Internal SCSI disk drives should have TERMPWR disabled. If it is not
and a second MBus module is added, any internal disk drives with PTC
protection may trip the power supply overcurrent protection when
powering up. Also, the internal cable 530-1874-02 has TERMPWR
grounded, which may trip the power supply overcurrent protection
with PTC-protected disks and blow fuses on fuse-protected disks.
The GT and ZX framebuffer options are not supported on boards with
MSI 100-2905-02 (labelled "LSI Logic L1A6396"). They are only
supported on board with MSI 100-2905-03 (labelled "LSI Logic
L1B7596").
501-1742
The 501-1371 P4 cgeight framebuffer must be -04 or later for use
with this board.
501-1889
Set the SPARCstation 10 clock speed to 66MHz.
SPARCstation 10 270-1733-08, -09, and -10 FABs require a crystal
change to support this module.
501-1899
The 501-1721 128M memory board requires boot ROM version 3.0 or
later.
The 501-1537/1538 VX/MVX Visualization Accelerator requires boot ROM
version 4.1.1 or later when used as the console.
501-2218
Set the SPARCstation 10 clock speed to 66MHz.
SPARCstation 10 270-1733-08, -09, and -10 FABs require a crystal
change to support this module.
501-2219
Set the SPARCstation 10 clock speed to 80MHz.
501-2239
Set the SPARCstation 10 clock speed to 72MHz.
SPARCstation 10 270-1733-08, -09, and -10 FABs require a crystal
change to support this module.
501-2258
Set the SPARCstation 10 clock speed to 80MHz.
501-2270
This board must be 501-2270-04 or later for use in the SPARCserver
1000 or SPARCcenter 2000.
Set the SPARCstation 10 clock speed to 80MHz.
501-2274
Internal SCSI disk drives should have TERMPWR disabled. If it is not
and a second MBus module is added, any internal disk drives with PTC
protection may trip the power supply overcurrent protection when
powering up. Also, the internal cable 530-1874-02 has TERMPWR
grounded, which may trip the power supply overcurrent protection
with PTC-protected disks and blow fuses on fuse-protected disks.
The GT and ZX framebuffer options are not supported on boards with
MSI 100-2905-02 (labelled "LSI Logic L1A6396"). They are only
supported on board with MSI 100-2905-03 (labelled "LSI Logic
L1B7596").
501-2318
66MHz control board 501-1671-04 is required.
This board is not compatible with system control boards 501-1671-05,
501-2335, or 501-2406.
501-2352
Set the SPARCstation 10 clock speed to 80MHz.
501-2359
Set the SPARCstation 10 clock speed to 80MHz.
501-2360
Set the SPARCstation 10 clock speed to 80MHz.
501-2361
Set the SPARCstation 10 clock speed to 80MHz.
The 501-2361-01 is for Sun internal use only and is tested for
operation at room temperature only.
501-2387
Set the SPARCstation 10 clock speed to 80MHz.
The 501-2387-01 is for Sun internal use only and is tested for
operation at room temperature only.
501-2377
Internal SCSI disk drives should have TERMPWR disabled. If it is not
and a second MBus module is added, any internal disk drives with PTC
protection may trip the power supply overcurrent protection when
powering up. Also, the internal cable 530-1874-02 has TERMPWR
grounded, which may trip the power supply overcurrent protection
with PTC-protected disks and blow fuses on fuse-protected disks.
501-2431
Set the SPARCstation 10 clock speed to 80MHz.
This module covers SBus slots 0 and 1.
501-2444
This module must be installed in the first MBus slot.
501-2445
This module must be installed in the second MBus slot.
This module covers SBus slots 2 and 3.
COMPATIBILITY (ROM): Boot ROM version 2.10 or later is required.
COMPATIBILITY (SUNOS): Solaris 2.3, with the Solaris 2.3 Supplement
CD (704-4195-10), is required.
501-8028
501-8028-07 or later is required to use the 501-8029 3/E color
framebuffer.
501-8035, 501-8058, 501-8064
Daughterboard 501-8013-05 is required if a customer-supplied PROM is
used with boot ROM version 1.6. Customer-supplied PROMs will not
function on daughterboards 501-8013-04 or below even if boot ROM
version 1.6 is installed.
BOOT ROM
========
501-1007
Boot ROM version N or later is required to run SunOS 2.0 or later.
Boot ROM version N or earlier may require jumping J1600 on
monochrome framebuffer 501-1052-01/02 when used with SunOS 3.0 or
later.
The 2/100U and 2/150U require boot ROM version Q (P/N
501-1103/1104-02) for the Sun VT100-style keyboard.
501-1051
Boot ROM version N or earlier may require jumping J1600 on
monochrome framebuffer 501-1052-01/02 when used with SunOS 3.0 or
later.
501-1074, 501-1094, 501-1163, 501-1164
Boot ROM version 1.8 or later is required to boot from a QIC-24 tape
in a Sun-3 shoebox (Emulex MT-02 controller?).
Boot ROM version 2.6 or later is required to boot from a QIC-24 tape
in a Sun-2 shoebox (Sysgen SC4000 controller?).
Boot ROM version 2.6 or later is required to boot from an SMD disk
attached via a 501-1249 Xylogics 7053 SMD controller.
501-1075, 501-1133, 501-1162, 501-1207
Boot ROM version 1.8 or later is required to boot from a QIC-24 tape
in a Sun-3 shoebox (Emulex MT-02 controller?).
Boot ROM version 2.5 or later is required to boot from a QIC-24 tape
in a Sun-2 shoebox (Sysgen SC4000 controller?).
501-1100, 501-1206
When "CPU EPROM 2.1" (probably boot ROM version 2.1) is installed,
two control-G's cause the keyboard bell to remain on until the
system is reset.
Boot ROM version 2.6 or later is required to boot from an SMD disk
connected to a 501-1249 Xylogics 7053 SMD controller.
501-1199, 501-1237, 501-1462, 501-1463, 501-1464, 501-1465, 501-1512,
501-1513, 501-1514, 501-1515, 501-1516, 501-1517
Boot ROM version 3.0 or later is required to use the P4 cgsix color
framebuffer (501-1374, 501-1505, 501-1532) as the console.
501-1205, 501-1322, 501-1334
Boot ROM version 1.6 or later is required to boot from a QIC-24
tape.
Boot ROM version 3.0 or later is required to use the P4 cgsix color
framebuffer (501-1374, 501-1505, 501-1532) as the console.
501-1208
Boot ROM version 1.8 or later is required to boot from a QIC-24 tape
in a Sun-3 shoebox (Emulex MT-02 controller?).
Boot ROM version 2.6 or later is required to boot from a QIC-24 tape
in a Sun-2 shoebox (Sysgen SC4000 controller?).
Boot ROM version 2.6 or later is required to boot from an SMD disk
attached via a 501-1249 Xylogics 7053 SMD controller.
501-1241, 501-1414
Boot ROM version 4.3 or later is required to use the GXi color
framebuffer 501-1352.
Boot ROM version 4.4 or later is required to use monochrome
framebuffer 501-1433 (and 501-1568?).
501-1274, 501-1491, 501-1522
Boot ROM version 1.7 or later is required to boot from an SMD disk
connected to a 501-1249 Xylogics 7053 SMD controller.
Boot ROM version 3.0 or later is required to use two or more
501-1576 16M memory boards.
501-1316, 501-1742
Boot ROM version 3.0 or later is required to boot from a QIC-24
tape.
Boot ROM version 3.0.1 or later is required to boot from a tape
drive connected to a second SCSI controller.
Boot ROM version 3.0.3 or later is required to use 4M SIMMs.
Boot ROM version 4.1.1 or later is required when the
501-1537/501-1538 VX/MVX Visualization Accelerator is used as the
console.
501-1324, 501-1413
Boot ROM version 4.3 or later is required to use the GXi color
framebuffer 501-1352.
Boot ROM version 4.4 or later is required to use monochrome
framebuffer 501-1433 (and 501-1568?).
501-1381, 501-1899
Boot ROM version 3.0 or later is required to use the 501-1721 128M
memory board.
Boot ROM version 4.1.1 or later is required to use the 501-1537/1538
VX/MVX Visualization Accelerator as the console.
501-1382, 501-1629
Boot ROM version 2.4 requires at least SunOS 4.1.1.
501-1632
Boot ROM version 2.4 requires at least SunOS 4.1.1.
501-1656, 501-1657, 501-1658, 501-1659, 501-1660, 501-1661
Boot ROM version 3.0 or later is required to use the P4 cgsix color
framebuffer (501-1374, 501-1505, 501-1532) as the console.
501-1686, 501-2055
Boot ROM version 2.8v2 or later is required to use SM41 MBus
modules.
Boot ROM version 2.10 or later is required to use SM51, SM520, or
SM521 MBus modules.
501-1689, 501-1835, 501-1870, 501-1974
Boot ROM versions 2.4, 2.6, and 2.9 in 2.x mode do not support SunOS
4.0.3c or 4.1. Set the NVRAM parameter "version2?" to FALSE to
enable the boot ROM 1.7 mode.
501-1733, 501-2259, 501-2365
Boot ROM version 2.12 is required to install two 501-2358 SM40 MBus
modules.
501-1866, 501-2334, 501-2362
The highest-revision boot ROM should be installed in motherboard 0.
501-2336
The highest-revision boot ROM should be installed in motherboard 0.
501-2352
Boot ROM version 2.10 or later is required in the 4/6xx.
501-2353
Boot ROM version 2.11 or later is required.
501-2360
Boot ROM version 2.10 or later is required in the 4/6xx.
Boot ROM version 2.11 or later is required in the SPARCserver 1000.
501-2361
Boot ROM version 2.10 or later is required in the 4/6xx.
501-2387
Boot ROM version 2.10 or later is required in the 4/6xx.
Boot ROM version 2.11 or later is required in the SPARCserver 1000.
501-2444
Boot ROM version 2.10 or later is required.
501-2445
Boot ROM version 2.10 or later is required.
501-2495, 501-2505, 501-2506
Boot ROM version 2.2 or later is required.
501-8035, 501-8058, 501-8064
Boot ROM version 1.4 does not support SunOS 4.1e, but versions 1.5
and 1.6 do.
SUNOS
=====
370-1388
Solaris 2.1 requires 370-1388-08 or later.
501-1007
SunOS 2.0 or later requires boot ROM version N or later.
SunOS 3.0 or later may require jumping J1600 on monochrome
framebuffer 501-1052-01/02 if the boot ROM version is N or earlier.
SunOS 4.0 or later requires jumping J701 unless the kernel has been
patched.
501-1051
SunOS 3.0 or later may require jumping J1600 on monochrome
framebuffer 501-1052-01/02 if the boot ROM version is N or earlier.
501-1075
Board revisions before 501-1075-10 may fail under SunOS 3.3.
The 370-1011 Sysgen SC4000 SCSI/QIC-02 tape controller does not work
with this motherboard under SunOS 3.3.
501-1133
Board revisions before 501-1133-10 may fail under SunOS 3.3.
The 370-1011 Sysgen SC4000 SCSI/QIC-02 tape controller does not work
with this motherboard under SunOS 3.3.
501-1134
Board revisions lower than 501-1134-07 Rev 50 may fail vid3.diag or
video3.exec.
501-1162
A bus error may occur when large executables are run during a
prefetch across a page boundary with CPU revisions lower than
501-1162-11.
Board revisions before 501-1162-08 may fail under SunOS 3.3.
The 370-1011 Sysgen SC4000 SCSI/QIC-20 tape controller does not work
with this motherboard under SunOS 3.3.
501-1207
A bus error may occur when large executables are run during a
prefetch across a page boundary with CPU revisions lower than
501-1207-04.
The 370-1011 Sysgen SC4000 SCSI/QIC-20 tape controller does not work
with this motherboard under SunOS 3.3.
501-1316
Board revision 501-1316-04 or later is required to run LISP
software.
501-1381
SNC 1.2 for Solaris 1.1 requires the 501-1381-01.
501-1382
The SPARCstation 1 was first supported in SunOS 4.0.3c.
Note that bug 1047696 in the installation of SunOS 4.1.1 and 4.1.1
Rev B causes trouble when mixing 1M and 4M SIMMs. "Install the 4MB
SIMMs in bank 0 when installing miniunix."
Sun Common LISP, AutoCAD, Cobol, and SunOS 4.1 require board
501-1382-08 or later and SPARC IU 100-1808-02 or later.
501-1627, 501-1680, 501-1720, 501-1748
The SLC was first supported in SunOS 4.0.3c.
Boards with the 53C90A SCSI controller require a patch to operate
under 4.0.3c.
501-1629
The SPARCstation 1 was first supported in SunOS 4.0.3c.
Note that bug 1047696 in the installation of SunOS 4.1.1 and 4.1.1
Rev B causes trouble when mixing 1M and 4M SIMMs. "Install the 4MB
SIMMs in bank 0 when installing miniunix."
Sun Common LISP, AutoCAD, Cobol, and SunOS 4.1 require board
501-1629-10 or later and SPARC IU 100-1808-02 or later.
501-1632
The SPARCstation 1+ was first supported in SunOS 4.0.3c.
Bug 1047696 in the installation of SunOS 4.1.1 and 4.1.1 Rev B
causes trouble when mixing 1M and 4M SIMMs. "Install the 4MB SIMMs
in bank 0 when installing miniunix."
501-1638, 501-1744, 501-1858, 501-1859, 501-1912, 501-1926, 501-1989,
501-1995, 501-2495, 501-2505, 501-2506
The SPARCstation 2 was first supported in SunOS 4.1.1.
501-1686, 501-2055
MBus module(s) SunOS/Solaris version
-------------- ---------------------
SM100 * 1 or 2 SunOS 4.1.2
SM41 * 1 SunOS 4.1.3
SM41 * 2 Solaris 2.1
SM51 * 1 SunOS 4.1.3
SM51 * 2 Solaris 2.1
SM52x * 1 or 2 Solaris 2.3
501-1689, 501-1835, 501-1870, 501-1974
The IPC was first supported in SunOS 4.0.3c.
CPU boards with the 53C90A SCSI controller require a patch to
operate under SunOS 4.0.3c.
Bug 1047696 in the installation of SunOS 4.1.1 and 4.1.1 Rev B
causes trouble when mixing 1M and 4M SIMMs. "Install the 4MB SIMMs
in bank 0 when installing miniunix."
Boot ROM versions 2.4, 2.6, and 2.9 in 2.x mode do not support SunOS
4.0.3c or 4.1. Set the NVRAM parameter "version2?" to FALSE to
enable the boot ROM 1.7 mode.
501-1733, 501-2259, 501-2365
MBus module(s) SunOS/Solaris version
-------------- ---------------------
SM30 * 1 SunOS 4.1.3
SM40 * 1 SunOS 4.1.3
SM40 * 2 Solaris 2.2
SM41 * 1 SunOS 4.1.3
SM41 * 2 Solaris 2.1
SM51 * 1 SunOS 4.1.3
SM51 * 2 Solaris 2.1
SM52x * 1 or 2 Solaris 2.3
501-1780, 501-1810, 501-1959, 501-2044, 501-2496, 501-2507
The IPX was first supported in SunOS 4.1.1.
CPU boards with the 100-2770-02 LSC L1A6341 ASIC are subject to bugs
1055265, 1057110, and 1057243 under SunOS 4.1.1 and 4.1.1 Rev B. The
IPX supplement fixes these bugs, and was rolled into SunOS 4.1.2.
Note that bug 1047696 in the installation of SunOS 4.1.1 and 4.1.1
Rev B causes trouble when mixing 4M and 16M SIMMs. "Install the 16MB
SIMM in U0310 when installing miniunix."
501-1861
The ELC was first supported in SunOS 4.1.1c.
Bug 1047696 in the installation of SunOS 4.1.1 and 4.1.1 Rev B
causes trouble when mixing 4M and 16M SIMMs. "Install the 16MB SIMM
in U0407 when installing miniunix."
501-1866, 501-2334, 501-2362
The SPARCcenter 2000 was first supported by Solaris 2.2 (SunOS 5.2).
Solaris 2.2 supports up to five system boards, or eight MBus modules
on four system boards.
Solaris 2.3 supports up to the full complement of twenty MBus
modules on ten system boards.
501-1889
SunOS 4.1.3 is required.
501-1899
SNC 1.2 for Solaris 1.1 requires the 501-1899-01.
501-2031, 501-2032, 501-2233, 501-2474
The SPARCstation LX/ZX was first supported in SunOS 4.1.3c.
501-2079, 501-2262, 501-2313
The SPARCclassic X was first supported in SunOS 4.1.3c.
501-2200, 501-2262, 501-2326
The SPARCclassic was first supported in SunOS 4.1.3c.
501-2218
SunOS 4.1.3 is required.
501-2219
SunOS 4.1.3 is required. Only one of these modules is supported in a
system.
501-2239
SunOS 4.1.3 is required.
501-2258
SunOS 4.1.3 is required.
Solaris 2.1 is required if two of these modules are installed.
501-2270
SunOS 4.1.3 is required.
Solaris 2.1 is required if two of these modules are installed.
501-2274
MBus module(s) SunOS/Solaris version
-------------- ---------------------
SM20 * 1 SunOS 4.1.3
501-2336
The SPARCserver 1000 was first supported by Solaris 2.2 (SunOS 5.2).
501-2352
SunOS 4.1.3 is required.
Solaris 2.1 is required if two of these modules are installed.
501-2353
Solaris 2.2 is required.
501-2359
SunOS 4.1.3 is required.
Solaris 2.1 is required if two of these modules are installed.
501-2360
SunOS 4.1.3 is required.
Solaris 2.1 is required if two of these modules are installed.
501-2361
SunOS 4.1.3 is required.
Solaris 2.1 is required if two of these modules are installed.
501-2387
SunOS 4.1.3 is required.
Solaris 2.1 is required if two of these modules are installed.
501-2377
The SPARCstation 10SX/10BSX was first supported by Solaris 2.3.
501-2431
Solaris 2.3, with the Solaris 2.3 Supplement CD (704-4195-10), is
required.
501-2444
Solaris 2.3, with the Solaris 2.3 Supplement CD (704-4195-10), is
required.
501-2445
Solaris 2.3, with the Solaris 2.3 Supplement CD (704-4195-10), is
required.
501-8035, 501-8058, 501-8064
SunOS 4.1e is not supported by boot ROM version 1.4, but is by
versions 1.5 and 1.6.